CROWN XTi2000
Descripción
Imágenes
Enviar a un amigo
Opiniones
Productos Relacionados
| Minimum Guaranteed Power, 1 kHz |
|
XTi 2000
|
|
| Per channel, both channels driven | |||
| Stereo, 2 ohms (per ch.) Stereo, 4 ohms (per ch.) Stereo, 8 ohms (per ch.) Bridge-Mono, 4 ohms Bridge-Mono, 8 ohms |
1000W*
800W 475W 2000W* 1600W |
||
| With 0.5% THD. *With 1% THD |
|||
The XTi Series of Crown amplifiers are professional tools designed and built for portable PA applications. The series includes three models which are identical except for output power: XTi 1000, 2000 and 4000. All are rugged and lightweight, and offer unmatched value in their class.
- Integrated proprietary DSP with LCD front panel display
- Accurate, uncolored sound with very low distortion for the best in music and voice reproduction
- Advanced protection circuitry guards against: shorted outputs, open circuits, DC, mismatched loads, general overheating, high-frequency overloads and internal faults
- Extremely versatile, handling a wide range of speaker impedances and outputs
- Switch-mode universal power supply
- Speaker presets for crossover frequencies, EQ, limiting, and delay
- All products fill 2U rack spaces and weigh under 17 pounds; weight sets a new standard in lightweight amps (20% less)
- Speakon® and binding post outputs, XLR inputs and loop-thrus
- Comprehensive LED status per channel
Specifications
| Sensitivity (volts RMS) for full rated power at 4 ohms |
1.4V
|
| Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
|
| Signal to Noise Ratio (below rated 1 kHz power at 8 ohms), A-weighted |
100 dB
|
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
|
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors. |
| AC Line Current |
XTi 2000: 6.9A,
At idle: Draws no more than 90 watts. |
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
|
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
|
| Load impedance (note: safe with all types of loads) Stereo Bridge mono |
2-8 ohms (4-8 ohms in XTi 1000 A1 100V versions)
4-16 ohms (8-16 ohms in XTi 1000 A1 100V versions) |
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
. XTi 2000: 32.9 dB.
|
| Maximum Input Signal |
+22 dBu typical
|
| Operating Temperature |
0° C to 40° C at 95% relative humidity
(non-condensing) |
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V, 220-240V 50/60 Hz
|
| Ventilation |
Flow-through ventilation from front to back
|
| Cooling |
Heat sinks and proportional-speed fan
|
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x12.25 in. (31.1cm) D |
| Net Weight, Shipping Weight |
18.5 lb (8.4 kg), 21.5 lb (9.8 kg)
|
Ningún mensaje encontrado
Añadir nuevo mensaje
|
|
||||||||
|
|
